Eibach Spring Group Buy

Discussion in 'For Sale by Businesses' started by brisz, Nov 19, 2010.

Thread Status:
Not open for further replies.
Page 4 of 4
  1. brisz

    brisz Well-Known Member

    Don't think Eibach USA would be able to help on that one, being that Aragosta are Belgium. Your probably best of emailing them or Eibach Germany.
     
    brisz, Mar 30, 2011
    #61
  2. ryzan

    ryzan Moderator Staff Member

    Bit of a bump on this one. Installed my springs along with my agx shocks from the other group buy. Had them on for about a week now and loving them (though they're a bit stiff for the roads around here) however one thing I have noticed is the top few coils are touching even when just sitting like so:

    [​IMG]

    [​IMG]

    [​IMG]

    Arer they supposed to be like this? Does anybody else's springs sit the same and if so why is this?
     
    ryzan, Apr 18, 2011
    #62
  3. brisz

    brisz Well-Known Member

    Just had a look at mine and are much the same.

    Had a bit of a search around and it seems to be part of a progressive rate design and or to stop the spring coming out of it seat when unloaded.
     
    brisz, Apr 18, 2011
    #63
  4. ryzan

    ryzan Moderator Staff Member

    Ah ok good to know, thanks :)
     
    ryzan, Apr 18, 2011
    #64
  5. AndyMac

    AndyMac Better than you

    This...
     
    AndyMac, May 9, 2011
    #65
  6. BoneZx

    BoneZx Active Member

    can someone that has these installed in there car. post of a pic of the ride height. just a pic looking at the wheel so you can see how high the guard sits off of the rim. cheers
     
    BoneZx, May 13, 2011
    #66
  7. brisz

    brisz Well-Known Member

    Im not going out in the bloody cold to take pictures, maybe tomorrow.

    But mind you how good is boost on a cold night, went out to pick up a pizza before and left a trail of bloodied noses, bloody hoons every where. :p

    Best one was this really rowdy AE86 sprinter, real nice looking red one. Came back for seconds and coped an uppercut. I was minding my own business he picked on me. :rolleyes:
     
    brisz, May 14, 2011
    #67
  8. Stef

    Stef Active Member

    The convertible has the Eibach springs.

    66cm front and 67 cm at the back

    [​IMG]

     
    Stef, May 14, 2011
    #68
  9. ryzan

    ryzan Moderator Staff Member

    [​IMG]

    Here's one I prepared earlier. (excuse the crappy phone camera)
     
    ryzan, May 14, 2011
    #69
  10. Sintrix

    Sintrix New Member

    Anyone got any more pics? Im looking at getting a set but I'm wondering how much of a gap there will be between my 18"s and the wheel arch.
     
    Sintrix, May 15, 2011
    #70
  11. brisz

    brisz Well-Known Member

    This might be of more help, measured all 4 corners at 660mm, but I fitted insertion rubber gasket between the strut tops and the body that was about 4mm thick, with out them height would be 656mm, pretty close to the 655mm I estimated in this above post. :p

    http://www.aus300zx.com/forum/showthread.php?p=1110637#post1110637

    [​IMG]

    Really enjoying the new springs they get rid of alot of the boat feeling that the kids on Boost Cruising label this car with, they have probably only seen a car with 20 year old suspension so that's all they know. Funny thing is the car probably came up a few millimeters from the sagged stock suspension. Enjoying the extra clearance.
     
    brisz, May 20, 2011
    #71
  12. Sintrix

    Sintrix New Member

    Thanks for that mate, but my problem at the moment is that i bought the car with non-stock springs. But they are WAY to hard... i practically get zero body roll even when i throw it really hard in to corners... the only problem is that i break my spine every time i go over a speed hump. So I'm wanting to soften my ride but lower it (not sure if its already lowered tho with the thicker springs)
     
    Sintrix, May 22, 2011
    #72
  13. brisz

    brisz Well-Known Member

    What is the height to the guard on all 4 corners and what tyre size are you running ?

    As per this drawing measure Hr and Hf, from the ground too the guard. (not the top of the tyre).

    [​IMG]
     
    brisz, May 22, 2011
    #73
  14. brisz

    brisz Well-Known Member

    I have only a couple sets left of each model.

    PM me your postcode for postage costs.
     
    brisz, Aug 7, 2011
    #74
  15. brisz

    brisz Well-Known Member

    Only 1 set of TT and 1 set of NA springs left, still including coil wrap free of charge, PM with postcode for post/freight cost.
     
    brisz, Dec 1, 2011
    #75
  16. brisz

    brisz Well-Known Member

    You know you want it you bitch.
     
    brisz, Dec 29, 2011
    #76
  17. brisz

    brisz Well-Known Member

    brisz, Jan 21, 2012
    #77
  18. beaver

    beaver southern zeds

    Thanks

    briz/John, that was quick:)
     
    beaver, Jan 27, 2012
    #78
Page 4 of 4
Thread Status:
Not open for further replies.

Share This Page