300zx Fibreglass Gauge Hoods (Stillen Style)

The "300zx Stillen 'Style' FGlass Gauge Hood" is a quality fibreglass Australian product and is suited to all RHD z32 300zx models.

Strong and lightweight, the guage hood is fitted with stainless hardware and comes with installation instructions, a protective seal to prevent marking your dash and optional installation screws.

The guage hood comes in black finish and can be used as is or painted.

The gauge face plates are available BLANK. You will need to cut/drill your own holes. ( photos show 60mm pre-cut holes )

These are available direct from the manufacturer at a very much discounted price of ...

AU$170 ( postage not included )

- 2 currently in stock
- 4 more arriving on the 25th August.

Each item is quality inspected by myself before shipping and have a 12 month manufacturers replacement warranty on structural workmanship.

Extra BLANK face plates are available at $15.00 ( postage included )

$15.00 surcharge if you want me to pre-cut 3 x 52mm or 3 x 60mm gauge holes.

Shipping - 'Registered & Insured' - Please allow 7 days for delivery from date of payment.

Qld. - $10.70
N.T. - $26.90
N.S.W. - $16.50
Vic. - $20.25
ACT. - $18.50
S.A. - $21.30
W.A. - $26.55
Tas. - $29.00








This For Sale thread is for the '2 gauge hoods currently in stock' and 'orders for the next 4' I am recieving on Monday 25th August.

First in first served. Reply to this thread using the template below and I will pm you the payment details. Please include your state or territory.


'2 gauge hoods currently in stock' ( will ship immediately )
1 -
2 -

'orders for the next 4' ( will ship on the 25/08/2008 )
1 -
2 -
3 -
4 -

Regards
Jason

 

(Excuse the dusty dash and the hood in the pics is my old original one, not one of the new ones for sale.)

Initially they are set into position with a little double-sided tape on the arms of the gauge hood.






While stuck to the center console, both are removed as one piece and a couple of holes are drilled through the console and into the arms of the gauge hood.



I use the top 2 holes as the lower one you have to be carefull not to drill completely through the arm. ( as I had done on my original hood )



Once the holes are drilled, remove the double-sided tape and run the provided weather seal around the edge of the hood to protect your dash ( taking care not to stretch it around the corners).



Then is just a simple case of screwing in the 2 screws either side.

Once it is all fixed together, your gauge hood and center console are 1 unit and you pop it all back into place in your dash.

Takes 30mins or less.

 

A better pic of the hoods.

 

I recived my gauge housing today in a well packed box. Basicly this item IMO suites the Z dash very well and inhances the look to give it more of a sporty feel. This housing mounts the gauges in a good position to monitor the reading of the gauges.

The fitment of this product is good and lines up well with the bottom of the housing to the dash with minimal gap.

As for the seller himself he was very helpfull and was more than happy to help with any problem I had.

Thanks jasonic for a awsome product

 

i demand more pics!

 

More of these due in early next week. (1/09/08)

Last 2 going to p5yk3r and wildzed.

@wildzed
Hey Dan, check your PM. I need your address mate.

 

hey mate can you save me one ? can pay on the 4th.

edit : i dont want holes in mine though

 

no prob. I'll contact you as soon as they arrive.

 

any more of these gauge holders left?

 

pm sent

 

Doing another run of these if anyone is interested.

A couple this month and another couple towards the end of March.

Sold a bunch of these last year. Have not heard any bad reports from anyone who purchased them.
Jason

 

i may be interested...how much in total including postage 2 NSW?

 

Possibly interested, depending on the finances.

Cheers,
Mike

 

me too how much to n.s.w 2756

 

Submitting my E.O.I

 

i want mine yesterday.

My EOI.

 

I really like the style of these , im in , hurry up will ya ...........lol :biggrin:

Trev

 

... one question ... your opening thread states something like .." .. hood is fitted with stainless hardware ..." ... wondering what this "hardware" might be ...????

 

Hey mate , been waiting for you to get some more :biggrin:
As per my PM to you at the end of the last batch ,,,will be in like flin for one this round.

Put me in the list this time please jasonic........:zlove:

Cheers
Patrick