QLD My Massive Sale Part 3 - Magnaflow, ToyZ, Ivan Tighe, JUN, HKS, Z1, 100K Kit, UR

Last thread was getting messy, so condensed it down to this.

Any questions please let me know. All this NEEDS to go, I want to clear the garage out so the next toy can come!! Happy to do discounts for multiple items, and PM me any offers.

***Please note well. Due to work I can only post items on Saturday mornings, if something happens with money transfers and the $$ are not in by Sat morning it will not be sent until the week after! All prices are +post***

Pickup from my place at Ferny Hills is preferred for the bulky items but will discuss shipping options if required, Australia post for all small items.


Custom 2+0 exhaust. 304SS, 2.5" mandrel bent. Twin in twin out magnaflow centre muffler with two 14816 at the end (the best Magnaflow's for a zed IMO ). Magnaflow 2.5" cats, can't recall the CPI, but are marked as CARB compliant. To suit 3" Toyz dumps, but could be easily adapted to standard or other dumps by any reasonable exhaust shop. Some of the welds are average as I did them, and some are excellent as they were done by a TIG expert $600!






Toyz 5 bolt 3" dumps. Drivers side one has been 'adjusted' slightly. Comes with a set of O2's, no guarantee's they work, I had them unplugged. $175!


Silicone radiator hoses $40!


Front steering tie rods $200 - Now $150!



Copy Stillen Nose Panel $75 - Now $60!



Aerocatches $75 - Now $50!


Alloy rad $120 - Now $80!


Sard attack meter $150 - Now $100!


Whiteline rear strutbar $100 - Now $75!


Ivan Tighe ground cams. Off new S2 blanks. Cam spec sheet to come, but like a better version of JWT's R4+, over $2k new. $1000



Spec sheet:


JUN Adjustable Intake Cam Sprockets. Allows adjustment of the timing of the intake cams. Removes VVT and look pretty cool S2 cams only. Includes bolts to go into cams. Excellent condition.. $350





JUN Adjustable Exhaust Cam Sprockets. Allows adjustment of the timing of the exhaust cams. S1 or S2 cams. As new $350



JEC's 740cc Injectors in Rail. S1 injectors, but with S2 plugs. Comes with S2 plugs to solder onto your loom. Rail includes fuel temp sensor. $450





Shortblock, OEM internals. Compression figures as noted previously. Heads and lower plenum has been ported by Eric at A2Zed. Includes heavy duty valve springs and heads relieved to fit 'proper' size cams New OEM head gaskets installed ~3000k's ago along with new OEM headbolts. Includes manual TT cams, but no timing parts $1750. Tried to take pictures of port work, didn't come out well at all



Little head markers.


Relieved for big cams :br:


HKS 2510 Turbos with HKS 5 bolt dumps. All oil and water lines, everything you need to bolt up to the VG30DETT. .49AR rear housings. Bush bearings. Have been stripped down and assessed by Eric and given a clean bill of health. I've been running them at ~12psi, never boosted higher than that due to fuel pump restrictions... Possible power?? 500-550hp I would expect, typical HKS with no compressor maps available. Includes HKS dual port wastegate actuators. Majority of manifold and turbo heat shields fit and bolt up too with some minor trimming. The exhaust and intercoolers were clean as a whistle when removed too. $1200










Ported OEM turbo exhaust manifolds. Work carried out by Eric (as with all the porting done). AMS/MS are too big, OEM too small, these are just right $200



100K service kit including timing belt, idlers, tensioner, water pump, cam and crank seals, crank sprocet, silicone water bypass hoses etc. Mix of OEM and generic parts. ~3000k's on them. Cam seals not shown but included, no AC belt and other belts are for NA PS and water pump with UDP fitted $200.



Unorthodox Racing Under Drive Pulley. Blingy blue! Gives more power and looks snazzy. Timing mark engraved and in correct place. Fits NA, TT, Manual and Auto $180




LS1 Engine Mounts. Stiffer and stronger than OEM Nissan. Bolt up and at correct height. Drilling out of the crossmember and engine mounts to 12mm required. Includes castle nuts and the lower tabs are cut off. 3000k's old $100


Z1 dual intake elbow kit. Includes tapered silicone elbows, brackets and hose clamps. $70


OEM S1 CAS. With bracket, in good working order. $50



OEM S2 Upper Plenum. With AAC, IACV, throttles and TPS. Modified to fit S1 injectors $150



OEM NA Power Steering pump with all brackets. Includes new high pressure hose made by Eric which is 3000k's old. $250



OEM PCV hoses and PCV's (not shown). You guessed it, 3000k's old... Rubber rather than the silly silicone which the clamps don't fit on. Includes all spring clamps too. $150 from Coz, $90 for my mates



Aftermarket Alternator. Unsure of output, no issues with it. 15000k's old I would guess. $100



OEM coilpacks, set of 6. Excellent working order, all with the little carbon electrodes attached. $120




Also got my turbosmart eboost street boost controller and OEM tt ecu on ebay. If you want them, bid on them. Links are:

Eboost Street

TT ECU

 

Well that was quick. Injectors and Z1 dual intake kit SOLD!

 

Radiator sold!

Come on people, spend up

 

pm sent....for Nose Panel

 

Nose panel sold!

 

Those manifolds look pretty good...

 

They come with the slicktop Mikey

They sure do You should buy them

 

Will my high flows need match porting? What about the block? Sorry, foreign to me!

 

I'm not exactly sure where he took the meat out of it. My understanding is that most of it is removed from the internals, rather than the flanges. Would be easy to match port it though, even with heads attached to the block.

 

Cool. I know match porting isn't difficult, more research necessary.

 

No worries

 

100K kit and UDP are likely sold.


Cleaned up the garage today and found these:

Goodridge front braided brake lines. Anti whip collars, name tags etc. $100 + post



Chili brake brace. Prevents fire wall flex and improves pedal feel. This is BRAND NEW never installed, out of the bag for the first time ever today just for pictures. Very likely to be the only brand new on still available. $120 + post


OEM 5 speed manual gear shifter. Excellent condition. Better than any aftermarket one I've used. $80

 

Chili brace for me, pm me.

 

Replied.


And silicone radiator hoses are gone too.

 

Following all sold!

SARD attack meter
Ported turbo manifolds
LS1 Engine mounts
ToyZ dumps

Also the Chili brace if zedboy PMs me back


Exhaust is on ebay Clicky

Also a couple of turbosmart BOV's
Type 1

Type 3

And because we have to have prices, $200 each, but just bid on the bastards, starting at $1.

 

I'll take Chili brace if zedboy doesn't

 

PM replied.

 

I'll take that OEM gear knob.

PM total inc. post to 4810 Townsville.

Cheers,

Adam

 

OEM Knob
Chili brace
100K kit
UR UDP
PCV's and hoses

All sold!

Not much left, come and get it and clear my garage out