QLD What's left sale.

Pictures in here
http://www.aus300zx.com/forum/showthread.php?t=327468


Stock engine,apparently rebuilt at some stage (no receipts) Good compression all cylinders between 145-150psi tested with long duration cams. Ported heads and heavy duty valve springs. Selling as a BARE engine. Can include stock cams and cams gears but wont be installed on engine. Timing belt kit is there also with low use. You can still read the writing on the belt.
$800 (nearly half what I paid with no timing belt kit only a few months back)

Complete custom made 3" Exhaust, 5 bolt ams dumps ceramic coated (a bit scratched up), high flow cats, one of the front pipes has a few dents from driving over rocks but doesn't affect performance, 2 resonators in the catback, magnaflow X pipe, twin magnaflow race mufflers also has 2 wideband bungs in front pipes. Perfect for anyone looking to make big power, cost was 2k+. If you have 4 bolt ams pipes they will fit the rest of the system.
$650 pick up only now.

Volk GT-C 17" wheels, front 8" +35, rear 9" +34.
$850

Z1 platinum steel driveshaft only ~1000km's use. No vibrations, uses the stock rear cv type joint,
hardy spicer yoke. cost was $800 landed in Aus.
$400

Gizzmo MS-IBC boost controller near new. Solenoid is missing screw in barbs.
$150 + post

Brand new Earls thermostatic oil sandwich plate 10AN fittings with right angle aeroflow fittings, I test fitted it with my setup and it would of fit okay.
$150 + post.

Earls 25 row oil cooler -10AN fittings + 4 Metres oil braided oil line + 4 aeroflow right angle bends and 2 hose ends.
$400 (or $500 with the thermatic sandwich plate)

Oil pickup new, gasket type.
$20

Aeromotive fuel pressure regulator -6AN fittings, brand new
$135

Good headlights $30 each.

Heater box with servos from 97 model zed very good condition works in my 89 model.
$30

Power steering pump rebuilt by me a while back also has a pirtek replacement hose (the one that normally leaks). Does not leak at all. Pump has had veins removed for HICAS delete and hoses looped.
$80

Stock TT rods with ARP bolts fitted, closed and honed by machine shop.
$100

5mm wheel spacers have the longer studs as well.
$30

Good working CAS
$50

6 Good working coil packs never had any problems at 20psi.
$60

Good working AUX fan from a 97 model had it working in my 89 TT
$40

Silicone brake booster and clutch hoses
$20

also have a pair of complete doors here $50 each or getting dumped.

Picture to give you an idea of offset on the wheels, front had -2.5 deg camber so look to sit in a bit more than normal.




also have a pair of complete doors here $50 each or getting dumped.

 

Would that oil setup entirely replace the stock kit? I'm guessing block off the existing lines?

 

Oil pan is sold pending pick up.

 

Hey mate
Is the tailshaft to suit 2 seater or 2+2, manual or auto, TT or NA???

 

2+2 manual TT

 

Bugger

 

SZ sump and power steering sold.

 

hey mate, you still got that interior?? and photos of the doors inside?

 

Long gone.

 

Okay want this stuff gone.

Engine $500
Exhaust $500
Pick up only.

 

Please pm me

 

Z1 platinum steel driveshaft only ~1000km's use. No vibrations, uses the stock rear cv type joint, hardy spicer yoke. cost was $800 landed in Aus.
$400

NA speed sensor pretty much brand new. Good for anyone that has done leader gears or NA rear end swap.
$100 delivered.


Everything else sold given away or gone to the dump.

 

Still have the engine by any chance??

 

its sitting firmly in my engine bay so i doubt it

 

Have you got a pic of the wheels on the car from the side

 

Couldn't find any straight on shots on the car, looking through my zed pics makes me miss the old girl.

 

everytime I look at S.A.P's front wheel my eyes go crosseyed ????

anyone else see something strange?



PS: I like the wheels, look good for 17" and the bonus is the optical illusion

 

Would the tailshaft suit a NA manual 2?2?

 

No the bolt pattern at the diff is diffetent, but Black beast said he will buy it anyway so sold.

 

yes sold