czp 1 piece propeller shaft

Discussion in 'Technical' started by jdmboy92, May 9, 2010.

  1. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    are these shafts any good have a bad feeling my centre bearing is no good could just replace bearing but rather than replace would like to upgrade
     
    jdmboy92, May 9, 2010
    #1
  2. Kieren

    Kieren Active Member

    Messages:
    935
    Likes Received:
    57
    Trophy Points:
    28
    Your Z has a propellor??? Bloody Americans, it's a driveshaft :p
     
    Kieren, May 9, 2010
    #2
  3. TWIN TERROR

    TWIN TERROR Well-Known Member

    Messages:
    1,105
    Likes Received:
    29
    Trophy Points:
    48
    Go to a boat ramp.Thats the place to find a prop shaft.
     
    TWIN TERROR, May 9, 2010
    #3
  4. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    haha i no but when i say driveshaft ppl think fwd driveshafts lol
     
    jdmboy92, May 9, 2010
    #4
  5. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    haha watever u no wat i mean lol
     
    jdmboy92, May 9, 2010
    #5
  6. Stef

    Stef Active Member

    Messages:
    2,437
    Likes Received:
    15
    Trophy Points:
    38
    A drive shaft, driving shaft, propeller shaft, or Cardan shaft is a mechanical component for transmitting torque and rotation, usually used to connect other components of a drive train that cannot be connected directly because of distance or the need to allow for relative movement between them.
     
    Stef, May 9, 2010
    #6
  7. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    so has anyone had any probs with this shaft???
     
    jdmboy92, May 9, 2010
    #7
  8. p5yk3r

    p5yk3r el8 haqur

    Messages:
    330
    Likes Received:
    7
    Trophy Points:
    18
    you mean, was anyone shafted? :rofl:

    ok that was bad.
     
    p5yk3r, May 9, 2010
    #8
  9. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    haha that was lame lol nice try tho
     
    jdmboy92, May 9, 2010
    #9
  10. Cam

    Cam ****

    Messages:
    2,642
    Likes Received:
    36
    Trophy Points:
    48
    I highly doubt that anything from Coz is shit but I can't say if they're any good or not. :eek:
    What's it worth including shipping. Could easily get one made up at your local "Tail shaft" :p shop.
     
    Cam, May 9, 2010
    #10
  11. jdmboy92

    jdmboy92 New Member

    Messages:
    73
    Likes Received:
    0
    Trophy Points:
    0
    haha 400us including shipping local tail shaft shop? in perth says 650 to rebuild mine
     
    jdmboy92, May 9, 2010
    #11
  12. ryzan

    ryzan Moderator Staff Member

    Messages:
    2,897
    Likes Received:
    150
    Trophy Points:
    63
    I've just put one in my car, haven't gone for a drive yet though as I'm doing my headers. If you can wait a few days I'll let you know what I think about it :) Cost me just under $470au landed
     
    ryzan, May 10, 2010
    #12

Share This Page