z1 3" dumps

Discussion in 'Non Technical' started by GYPO, Apr 30, 2009.

  1. GYPO

    GYPO Chasing 10's

    Messages:
    155
    Likes Received:
    0
    Trophy Points:
    16
    Hey all,

    just wandering if anyone has had experience with the above? Are they a direct bolt on, even though we steering is on opposite side of the car? or will there need to be mods????

    Any comments appreciated.....

    Thanks,
    Gypo
     
    GYPO, Apr 30, 2009
    #1
  2. WazTTed

    WazTTed Grease Monkey

    Messages:
    6,171
    Likes Received:
    44
    Trophy Points:
    48
    do z1 even make there own ones ???

    SZ do tho
     
    WazTTed, Apr 30, 2009
    #2
  3. GYPO

    GYPO Chasing 10's

    Messages:
    155
    Likes Received:
    0
    Trophy Points:
    16
    Alloy toyz 3" dumps not Z1

    my bad - alloy toyz 3" dumps.....
     
    Last edited: Apr 30, 2009
    GYPO, Apr 30, 2009
    #3
  4. ZEDZY

    ZEDZY Active Member

    Messages:
    1,183
    Likes Received:
    6
    Trophy Points:
    38
    I think the AMS ones fit. I think these are the same ? :confused:
     
    ZEDZY, May 1, 2009
    #4
  5. Vuk@AMS

    Vuk@AMS New Member

    Messages:
    248
    Likes Received:
    11
    Trophy Points:
    0
    They distribute the AMS units made for us. We have the 'At-Par Special' still happening so contact either our Aussie Rep or us directly for more info.

    They fit with no issues as we've installed them on several RHD vehicles.

    Regards,

    Vuk@AMS
    www.amszstore.com


     
    Vuk@AMS, May 1, 2009
    #5
  6. rob260

    rob260 Administrator Staff Member

    Messages:
    13,705
    Likes Received:
    689
    Trophy Points:
    113
    Location:
    Sydney (North)
    Look for brisz thread regarding sz dump pipes. Magicmike has a pair of these ams pipes on his car, he and drz400y (who did the install) posted some comments re quality and fitment.
     
    rob260, May 1, 2009
    #6
  7. Vuk@AMS

    Vuk@AMS New Member

    Messages:
    248
    Likes Received:
    11
    Trophy Points:
    0
    http://www.aus300zx.com/forum/showthread.php?t=287933

    Also another thread albeit a little more heated:

    http://www.300zxclub.com/showthread.php?t=153417&highlight=ams

    As mentionioned with 'Par' deals any small adjustments may be worth it to most, especially considering the seperator more often needs adjusting regardless of manufacturer.

    Regards,

    Vuk@AMS
    www.amszstore.com







     
    Vuk@AMS, May 1, 2009
    #7
  8. GYPO

    GYPO Chasing 10's

    Messages:
    155
    Likes Received:
    0
    Trophy Points:
    16
    nice....thanks for the reads and info!!!!!!!!!
     
    GYPO, May 1, 2009
    #8
  9. honzrr

    honzrr New Member

    Messages:
    47
    Likes Received:
    2
    Trophy Points:
    0
    for the record, i have seen several of the SZ pipes crack, in person, but i have yet to hear of a problem with a single AMS/AT pipe. sure, some may say the SZ look a little prettier, but i'd take reliability any day (and cost savings).
     
    honzrr, May 2, 2009
    #9
  10. Vuk@AMS

    Vuk@AMS New Member

    Messages:
    248
    Likes Received:
    11
    Trophy Points:
    0
    No probs! Buzz us if you have any specific questions in the future!

    Regards,

    Vuk@AMS
    www.amszstore.com


     
    Vuk@AMS, May 2, 2009
    #10

Share This Page