QLD Parting Out Two VG30DE's

Got two VG30DE's I'm parting out. Both are manual motors.

Coilpacks $10 ea (have 12)
Balance tubes $40 ea (have 2)
Upper plenum's $100 ea (have 2)
Lower plenum's $50 ea (have 3)
Series 1VVT intake gears $50 a pair (have 3 pairs)
Exhaust cam gears $30 a pair (have 3 pairs)
Near new water pump $50
Near new tensior and idlers and timing belt $100
Manual cams $200 a set of 4 (have 2 sets)
VVT solenoids $10 ea (have 4)
Valve covers $50 a set (have 2 sets)
NA fuel rail and injectors $100 ea (have 2)
Fuel regulator $40 ea (have 2)
Fuel dampener $20 ea (have 2)
Timing belt covers, VGC $60
IACV $50 ea (have 2)
AAC $50 ea (have 2)
Throttles $80 a set (have 2 sets)
CTS $20
Temp gauge sender $10
Water hard pipes $40 for both
Standard balancer $50 ea (have 2)
Good Air con comp $150
Standard intake hose pipe things with no splits $50 a pair
S2 PTU with adaptor harness $100

Short block (i.e. what's left after I remove the above) $300 ea. One has good compression (the one out of my black 2+2) 160ish across the board, have a search there was a thread with the results in.

The other I'm not sure about and can't be bothered to test. Crank still turns, no dodgy noises. Both can be used to build a TT if you are using aftermarket forgies. They have the correct oil squiters for them too.


Also have:

NA manual radiator VGC with shroud $100

Radiator hoses, upper and lower. Look about 6 months old, very soft and nice. $50 for both.

I'll take piccies if wanted. Just let me know.

I DO NOT HAVE ANY POWER STEERING PUMPS

 

I will take the ptu. U have a pm

 

i'll take coil packs 6 of them would be sweet thanks Bryan

 

Temp gauge sender for me please

 

chrispy

how much for a pair of heads

 

OK, I'll Pm details soon.

$150 a pair, can't guarantee that they will servicable. The one out of the 2+2 has been cooked a few times, not sure about the other.

 

will they

be rebuildable

 

Don't know, depends on how soft they are now. It is possible that they are warped too. You never know till you take them to get rebuilt.

 

well

nevermind then

 

i will take the radiator hoses

 

Any power steering pumps?

 

however

i will take a fuel reg. i'll pick it up from amec if you are there next saturday.

 

pm sent

Pm sent

 

Update time with piccies!

Coilpacks $10 ea (have 6)
Balance tubes $40 ea (have 2)
Upper plenum's $100 ea (have 2)
Lower plenum's $50 ea (have 2)
Series 1VVT intake gears $50 a pair (have 3 pairs)
Exhaust cam gears $30 a pair (have 3 pairs)
Near new water pump $50
Near new tensior and idlers and timing belt $100
Manual cams $200 a set of 4 (have 2 sets)
VVT solenoids $10 ea (have 4)
Valve covers $50 a set (have 2 sets)
NA fuel rail and injectors $100 ea (have 2)
Fuel regulator $40 ea (have 1)
Fuel dampener $20 ea (have 2)
Timing belt covers, VGC $60
IACV $50 ea (have 2)
AAC $50 ea (have 2)
Throttles $80 a set (have 2 sets)
CTS $20
Water hard pipes $40 for both
Standard balancer $50 ea (have 2)
Good Air con comp $150 maybe sold
Standard intake hose pipe things with no splits $50 a pair
CAS's $75 ea (have 2)
TPS $50ea (have 2)

Both short blocks still available


Also have:

NA manual radiator VGC $70

Clutch fan in excellent condition no cracks at all. $70


Clutch fan clutch, good nick $40

Anything else you can see here:

 

Do you have an NA power steering pump? :thumbup:

 

:bash: Shut up you old codger!


Clutch fan sold!

 

what about the clutch fan clutch?

 

Clutch fan clutch still available!

 

dibbs...

 

One lower plenum and one set of VVT gears left...

No tensioner or idler bits, they are all stuffed. The ones off my original motor were in the weather too long and the other ones were never changed at the 'supposed' 100K.