Zed is on the mend

You can come around and look at the wiring on my car if that's any help.

 

Will do.

You are a champ Mick. Your car is so neat. I hope to have mine at that level someday. But it won't be for some time.

 

Can these injectors be used with E85

I am not planning on running it now. But I want the choice if it's required in the future. was going to buy the cheap Jecs which are a direct replacement for 90 mods.

These come with a conversion kit though and are reasonably priced. So if all good I am getting a set.

Cheers


http://www.conceptzperformance.com/...&Car_Type=300&UID=20110614234029119.12.64.123

 

You want the S2 pintle-less injectors.

 

that is what I was asking

the above link is for 95 onwards..so they would be series 2 and therefore E85 compliant???

 

I think this is what you want 95+ http://www.conceptzperformance.com/...&Car_Type=300&UID=20110614234029119.12.64.123

 

Thanks but they are exactly the same

as the kit I was asking about minus the adapter kit for the 1990-93 model which is what mine is. So looks like they will be fine then.

Cheers

 

So the time has come to sell

and I checked out carsales for an idea on what they are worth. It seems there are many of them around 6k!!! This is crazy if I wasn't such an outstanding citzen I would burn the bastard out and get some insurance money.

I just offloaded a mint xr6 for 12k and thought I got ripped on that. But I have spent easy 30k on the zed and I might get 6k if I am lucky. If it seems I am having a whinge, it's because I am. Thanks and good day

 

apples and oranges

a beat up no maintenance money pit zed for 6 K.

A rebuilt/refurbed one 12-15K at a guess depends how patient you are

 

Ok so I'm resurrecting this thread because I am at the point of pulling what little hair I do have out. Apart from the windsreen washer bottle that hopefully madcow can supply me with my car is just about restored to factory appearance. Only problem I have is the loom that runs to the receiver dryer and the AMB temp sensor.

When I had the radiator support bracket replaced with new, the body shop decided to grind straight through that loom. No problem I can just re-wire it up. But no....I'll be buggered if I can find where the remaining bit of loom is gone. Perhaps they have taped it up and I can't see it? I thought it ran from the same loom as the fog lights and loom for the washer bottle pumps etc?? Anyone got any ideas? I really want to get this thing perfect and about 5 tiny wires are stopping me from this. Cheers people

 

Ill hunt around for a bottle. If i got one come past and see where the wires are on my car.

 

Will be one out at the property if you didn't pull it out, looks like 2+2 from profile pic. No idea on condition.

 

Thanks guys. Madcow if you could check that out then I finally have all the parts As for the wires I was checking them out on a wreck and the damn thing should be right where I thought it was. I'll have to dig a bit deeper.

 

Look forward to seeing it come together!

 

i got a radiator overflow. Not a window one

 

poo

I need a window one. Maybe I can just get mine plastic welded so it doesn't dump it's guts in 5mins

 

Fists will have One on his Shell

 

Is this what your after http://tech.aus300zx.com/photo/eb/eb27.jpg ?

If so i've got one sitting in my spares box

 

Cheers but no

I'm after the one on the other side of the car. For the windscreen washer. Just so I can get it roadworthy again

 

Ahhh this is what your after

http://www.ebay.com.au/itm/Nissan-3...nd-/171654326415?_trksid=p2141725.m3641.l6390