VG30dett stroker kit for sale at 999.99USD on ebay

Discussion in 'Car Parts for Sale or Wanted' started by JFRacing, Jul 8, 2009.

Thread Status:
Not open for further replies.
Page 2 of 2
  1. LazyZed

    LazyZed Active Member

    Messages:
    1,255
    Likes Received:
    3
    Trophy Points:
    38
    I am SORELY tempted, but house has to come first too :(

    Maybe I can get away with it....what the missus doesn't know.... ;) :zlove::nono:

    EDIT: If it is available next week (pay week ;) ), then I might just pick it up ;)

    Cheers
    Rob
     
    LazyZed, Jul 10, 2009
    #21
  2. selliver

    selliver New Member

    Messages:
    183
    Likes Received:
    0
    Trophy Points:
    0
    How much work is this anyways, who would do it etc ?
    what are all the gains you would get ?
    Im just curious i know nothing about it aye ... :(
     
    selliver, Jul 10, 2009
    #22
  3. JFRacing

    JFRacing Old new member

    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    6
    Normally, sleeving block by Darton with custom sleeve turn around 1500-2000$ US. The gain is 1 Litre. You will gain a lot of torque and gain hp too. The turbo will spool a lot quiker because the turbo work on 2l vs 1.5l in stock block.
     
    JFRacing, Jul 11, 2009
    #23
  4. selliver

    selliver New Member

    Messages:
    183
    Likes Received:
    0
    Trophy Points:
    0
    Sounds pretty awesome to be honest !
    Much work involved with the whole process ?
     
    selliver, Jul 11, 2009
    #24
  5. JFRacing

    JFRacing Old new member

    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    6
    the same work as when you rebuilding engine.
     
    JFRacing, Jul 11, 2009
    #25
  6. Drift Spec

    Drift Spec New Member

    Messages:
    461
    Likes Received:
    0
    Trophy Points:
    0
    Still available??
    PM sent
     
    Drift Spec, Jul 11, 2009
    #26
  7. ZXXXII

    ZXXXII New Member

    Messages:
    176
    Likes Received:
    0
    Trophy Points:
    0
    specs

    is it possible to get the specs of the crank rods and pistons as im sure could get one made or similar from stroke me racing

    also i think diesel dave has his sleeved i know he was saying he took it right out to the cooling gallerys
     
    ZXXXII, Jul 11, 2009
    #27
  8. JFRacing

    JFRacing Old new member

    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    6
    I dont relly understand your question. Pistons was Venolia 97mm, stock size rod and Paeco crankshaft. You can try to contact Paeco to know the spec.

    http://www.paeco.com
     
    JFRacing, Jul 11, 2009
    #28
  9. JFRacing

    JFRacing Old new member

    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    6
    Sold pending payment
     
    JFRacing, Jul 11, 2009
    #29
  10. JFRacing

    JFRacing Old new member

    Messages:
    52
    Likes Received:
    0
    Trophy Points:
    6
    SOLD

    Close this tread
     
    JFRacing, Jul 11, 2009
    #30
  11. Drift Spec

    Drift Spec New Member

    Messages:
    461
    Likes Received:
    0
    Trophy Points:
    0
    Cheers JF:D:D
     
    Drift Spec, Jul 11, 2009
    #31
Page 2 of 2
Thread Status:
Not open for further replies.

Share This Page