Disconnecting Sun Sensor

Discussion in 'Technical' started by rob260, May 6, 2011.

  1. rob260

    rob260 Administrator Staff Member

    Ok..... is there any trick to disconnecting the sun sensor from the dash? As in disconnecting the harness plug? Been at this thing for fifteen minutes now and it doesn't want to play.... and I don't want to break it!

    Any ideas? Is it just a case of push down and pull?

    Also mods if you are reading it might be worth adding "sun" to three word search list
     
    rob260, May 6, 2011
    #1
  2. Chrispy

    Chrispy Pretentious Upstart

    I've never had too much trouble. Get that silly foam around the plug off and it should be clear.
     
    Chrispy, May 6, 2011
    #2
  3. rob260

    rob260 Administrator Staff Member

    I've thought about that, but I'm assuming the foam is there for a reason.... keeping heat out of the plug? But yes very, very tempted
     
    rob260, May 6, 2011
    #3
  4. Chrispy

    Chrispy Pretentious Upstart

    To stop it rattling I would assume.

    I've always pulled the foam off.
     
    Chrispy, May 6, 2011
    #4
  5. Peter Black

    Peter Black Active Member

    It looks like pretty generic packing foam to me so if it really bothered you you could always re-wrap it in some new foam. My foam was glued on so I had to take it off before I could undo the connector.
     
    Peter Black, May 6, 2011
    #5
  6. MagicMike

    MagicMike Moderator Staff Member

    What sun sensor? The thing in the dash vent? If so they have always been tuff to unclip but a small screwdriver to press the clip down while pulling works...
     
    MagicMike, May 6, 2011
    #6
  7. Altari

    Altari '89 2+2 TT Manual

    What do they even do?
     
    Altari, May 6, 2011
    #7
  8. Vader

    Vader Just another guy

    'Reads' the amount of sun hitting the dash so the climate control can adjust for it.
     
    Vader, May 6, 2011
    #8
  9. Tektrader

    Tektrader Z32 Hoe, service me baby

    Nah just peel back the foam and unplug it. The foam is just there so it doesnt rattle.
     
    Tektrader, May 6, 2011
    #9
  10. Vader

    Vader Just another guy

    +1.

    Just pull a bit of bubblewrap out of a $1 postbag and re-wrap it when done.
     
    Vader, May 6, 2011
    #10
  11. rob260

    rob260 Administrator Staff Member

    Took your advice.

    Foam off, plug disconnected, caulking gun broken... I don't think it liked trying to pump sika through vac line.

    There's never an "easy way" hey
     
    rob260, May 6, 2011
    #11
  12. You Mad

    You Mad New Member

    Why do u want to d/c the sensor??
     
    You Mad, May 6, 2011
    #12
  13. rob260

    rob260 Administrator Staff Member

    To pull the vents out and glue the dash down
     
    rob260, May 6, 2011
    #13
  14. You Mad

    You Mad New Member

    Do you think if the sun senor didnt work it would mess up the aircon system ??
     
    You Mad, May 6, 2011
    #14
  15. Altari

    Altari '89 2+2 TT Manual

    Worth it. On my NA I pulled the dash to change the heater core out, and fixed the dash lift in the process. Very worth doing. :)
     
    Altari, May 6, 2011
    #15
  16. stevearm77

    stevearm77 NA Compression + TT Boost

    Geez, you learn something new about these cars everyday
     
    stevearm77, May 8, 2011
    #16

Share This Page