300zx widebody kit by diamond autocraft

Discussion in 'Non Technical' started by TigerZ, Nov 26, 2009.

  1. TigerZ

    TigerZ New Member

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    0
    Thoughts on this?? (Not sure if this is a re-post)

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]


    TigerZ
     
  2. muffler

    muffler New Member

    Messages:
    31
    Likes Received:
    0
    Trophy Points:
    0
    that look shit
     
  3. directzx

    directzx New Member

    Messages:
    543
    Likes Received:
    7
    Trophy Points:
    0
    looks sh*t


    why cant someone just make a nice, simple widebody kit that takes the original lines of the z32 and exaggerates them just a little bit?


    something that will look good riveted on, Not glassed.. Please ??
     
  4. URHYNS

    URHYNS Well-Known Member

    Messages:
    1,154
    Likes Received:
    41
    Trophy Points:
    48
    Horrendus.
    Thanks for sharing, again.
     
  5. psycodelik

    psycodelik psyco led's

    Messages:
    976
    Likes Received:
    5
    Trophy Points:
    0
    ummmmm..... [TIS][TIS][TIS]
     
  6. yellow300zx

    yellow300zx Pimpin Ain't Easy

    Messages:
    266
    Likes Received:
    7
    Trophy Points:
    38
    Gonzo's was pretty nice.
     
  7. Steven

    Steven Active Member

    Messages:
    946
    Likes Received:
    14
    Trophy Points:
    38
    Too Busy

    Too Busy...

    Too many side lines ... I would get rid of the air intake which faces forward in from of the rear wheel arch. But I will say that the rear does change the rear shape to make the car look something other than a 300zx. I could see the car in a metallic orange or a deep candy-apple-red.
    [​IMG]

    The front nose looks too big ... it needs to be broken up with a pair of standard indicator lights and square driving lights.
    [​IMG]

    Ummm, how do I unlock the boot?
    I would scope the outer ends of the rear diffuser to match up with the inner edge of the side taillights.
    [​IMG]

    Front bar, side panel, and centre panel as one piece is STUPID from a logistical point of maintenance and repair. "oh, wait I have to remove the whole front end to clean the air-intake pod-filter, and god I hate driving in autumn the leaves get stuck in the nose". ... should be three distinctive pieces.
    [​IMG]
     
  8. ed300zx

    ed300zx Active Member

    Messages:
    3,661
    Likes Received:
    5
    Trophy Points:
    38
    i like it. not as a modded 300zx but just as a car in general
     
  9. Kieren

    Kieren Active Member

    Messages:
    935
    Likes Received:
    57
    Trophy Points:
    28
    They've just made a new car.... where's the 300ZX?????
     
  10. ed300zx

    ed300zx Active Member

    Messages:
    3,661
    Likes Received:
    5
    Trophy Points:
    38
    exactly....and thats what i mean by my comment, i like it as a car (as in a new car) but not as a modded 300zx (because there isnt much stock zed left(body shape wise))
     
  11. Chrispy

    Chrispy Pretentious Upstart

    Messages:
    12,888
    Likes Received:
    368
    Trophy Points:
    83
    I like it better than the Strosek kit. It's not too bad I reckon. Really digging the back.

    Can't take any styling advice from you Steven, you have Ferrari lights :p
     
    MagicMike likes this.
  12. cherryZ

    cherryZ Truth Addict

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Arse end looks like a modern interpretation of the Porsche 928. I think it could look pretty tough... but definitely no point calling it a Z.
     
  13. MagicMike

    MagicMike Moderator Staff Member

    Messages:
    7,405
    Likes Received:
    134
    Trophy Points:
    63
    :rofl:[TIS]

    I don't mind the rear bar section, rest is ok. Not worth the drama to fit tho...
     
  14. THEZED

    THEZED Loose Screws Inside

    Messages:
    548
    Likes Received:
    0
    Trophy Points:
    16
    I think the front looks agreeable and the rear as well. However the side is too angular. It looks too square/boxy. However as some as said, it looks like a entirely different car, not the 300zx. Maybe the future of the 300zx now renamed 300z (as opposed to the 350z and 370z) in an alternate universe........ :p
     
  15. JD-3193

    JD-3193 New Member

    Messages:
    402
    Likes Received:
    0
    Trophy Points:
    0
    I actually think I like it! I'd have to see it sprayed with the indicators in though.
    I'm imagining it in bayside blue... :zlove:
     
  16. jaybo

    jaybo New Member

    Messages:
    2,481
    Likes Received:
    3
    Trophy Points:
    0
    whoops!
     
  17. Benny_C

    Benny_C About as subtle as...

    Messages:
    4,639
    Likes Received:
    133
    Trophy Points:
    63
    Location:
    Toowoomba, Qld
    I actually like it! putting aside the fact that it completely changes the shape of a stock Zed, it still looks like a very agressive body kit! i'd have one! :eek:
     
  18. JD-3193

    JD-3193 New Member

    Messages:
    402
    Likes Received:
    0
    Trophy Points:
    0

    ...Do it :D
     
  19. dannY_trev

    dannY_trev Member

    Messages:
    350
    Likes Received:
    0
    Trophy Points:
    16
    i like it too, would be interesting to see what happens with the rear lights but i think the zx rear is beginning to look dated.. would look great with a diffuser of some sort, and maybe a bigger opening on the front bar
     
  20. JD-3193

    JD-3193 New Member

    Messages:
    402
    Likes Received:
    0
    Trophy Points:
    0
    The indicator slots at the back look kinda similar to a 350Z.

    [​IMG]
     

Share This Page