ANGEL EYES

Hey Guys,

As seen in this thread
ANGEL EYES

Im going to be making a few more sets of these and making up instructions for installation aswell.

COST: $65 including postage to anywhere in australia.

It includes two angel eyes made the right size to fit around our projector rings inside the headlight, they come with wiring so all you need to do is hookup the positive and negative of the angel eyes and your ready to go.
also they can either be switched or wired into parkers.

Can be either BLUE or WHITE

Installation takes about 30 minutes to take headlights out,
one hour to melt lights, install angel eyes, then put lights back together.
then another 20 minutes or so to reinstall headlights.

Ill be writing a very detailed instruction sheet on how to install these angel eyes so you cant go wrong at all.

For those Interested PM me for any more details.

White is ready when wanted, but i cant make blue's for the next week or so until iv sourced more Blue LED's

Enjoy :zlove:

 

im in ..

ill let you know what color i want tonight ..


when you say blue ,,, how blue is it ???

it would be good if you can make 1 set up to show the color of the blue ... side by side with the white .. can this be done ......soon..

p.s can we get the light to go all the way around , 360 degree

 

If only they were completely circular I would be keen. Makes the Z have happy eyes like this

 

an example is this
it would be the blueness of the bars running along, slightly less bright

blue can be done in the next week, im gonna go through all my spare led's and try and make up atleast enough for one angel eye, will see what i can do tonight.

you can get the light the whole way around, but the problem is that then you get a major brightness spot where the led's sit.

but covering them up, leaving the gap at the bottom, it means you get a relatively even glow the whole wa around the ring as you dont see the very bright led's, but ill have a go later trying to make a full ring.

 

ok . do what you can man let me know .

I'm thinking i will go with the white ones . but will let you know tonight .

the blue ones would look good ( but its the cop thing for me )

see if you can go all the way around ..

either way I'm in ..

but would like it all the way around ..

p.s great job you done there

 

What do you mean by melt lights?

 

haha thanks man, glad you like them.

stiive: by melt the lights, you take out the headlight, or you could do it in the car i guess on a really hot day or with a heatgun,

but you rest the headlight in the opening of the oven door, set to 150 degrees, for 10 mins, glass side facing the heat.
then after 10 mins, you just take it out and separate the glass from the back of the light, its a piece of piss, and absolutely nothing compared to taillights.

the instruction sheet will include photos and easy step by step guide on how to put them in

 

im in

hey mate i will take a set of these and keepin with the engine bay colour gonna have to go blue

 

k mate sounds good, i will be pming people in the order theyve shown interest when i get them made, for now there will be a week delay on the blue ones as i need to order led's.

 

To clarify.. you can wire them to come on whenever the parkers are on?

 

Hate to be a kill joy, but say if you were pulled over and given a defect for the blue angel eyes. You would have to replace the whole headlight, Is that right?

 

very easily, its just a positive and negative, so on mine i ran the wires out the back of the headlight, then down into the front bar and parkers, then joined them onto the parkers negative and positive.

also, so people know there is no visible wiring, depending on what angkle you mount them there might be a tiny bit, but the way i did it there absolutely zero.

if you were defected, to clear the defect you would have to remove the halos, and prove that the headlight no longer has a blue ring. not replace the whole headlight itself. but then again you can get defected for eyelids, HID's, etc.

 

can i get a set of white ones?

 

posted my interest in previous post for a white set

 

im after a set of blue ones.

but waiting to see the dummy photos.

also just a question, if you cant make a complete circle because of the heat, is there any chance you could make the circle closer to being complete? like as in almost complete the circle but leave less of a gap between the buttom?
i.e - a 6 l.e.d gap at the buttom could become a 3 l.e.d gap?

kindest regards.
rod.

 

hypedz yeah for sure man, ill put you down for a set

atm i havnt started making them as im getting my old work to make up a jig for me to make them perfectly round, which was the issue with mine taking 4 gos to get correct.

im gonna try and make a full circle, but
its not because of heat, theres a gap as i use black heatshrink to cover that section, ie, the led's. as if you can see the led's its far brighter than the rest of the ring and can look out of place, but im gonna play around with it anyway.
so yeah ill give it a go in white and blue, just havnt had the chance yesterday or today, will see how tomorrow goes in not will definately have the demos done by this weekend.

 

interested pending demos

 

This thread will move shortly to the group buys section.

 

I'm definately in, put me down for white, however, I want to see blue first... cos I could be tempted... although, to reduce the attention from the LEO's, I'll probably go white

 

yeah im the same .. i would rather the blue all the way, but if the cops get me , its a big job to take out ....

but i would like to see the blue as well .

im in 100% either way ...