Radiator SS T Bolt clamp set GB........

Discussion in 'Group Buys' started by zx299, Jan 25, 2016.

Thread Status:
Not open for further replies.
  1. zx299

    zx299 Well-Known Member

    I've been asked to run a Group Buy on a Stainless Steel T Bolt clamp set to fit the Radiator and hardpipe on a 300ZXtt

    [​IMG]

    These SS T-Bolt clamps have a full 19mm width band, which eliminates the clamp cutting into the hose as it's tightened. The T-Bolt clamp has a superior action, and can be tightened to far greater torques without twisting or stripping. And because they're Stainless Steel, they'll add a bit of bling under your bonnet

    These SS T Bolt clamps are the same high grade clamps used in all our previous Group Buys so you can be assured of their quality

    The full set (6 clamps) is available at a GB price of $18 and we'll need a minimum of 10 starters to secure the price. Because this is a low volume GB, it will only run for about a month. This is a perfect opportunity to get rid of that mangled assortment of worm gear clamps you currently have on your radiator :eek:

    Parcel Post is $8.25 (within Australia) so put your hand up to be in the GB or PM me if you have any questions :cool:
     
    Last edited by a moderator: Jan 25, 2016
  2. zx299

    zx299 Well-Known Member

    We have a few starters already.....

    but we need some more...... this GB will NOT run for very long so don't sit and think about it, put your hand up :)

    These SS T bolt clamps are top quality and will outlast your zed, so grab these and it will be the last radiator clamps you will ever buy :cool:
     
  3. mrkarter77

    mrkarter77 No Really, They do!!!

    Sign me up.
     
  4. FireHorse

    FireHorse Member

    1. mrkarter77
    2. FireHorse
     
  5. wildzed

    wildzed Member

    ill be in for a set
     
  6. pmac

    pmac Z,, IT'S COMPLICATED!!!!!

    Clamps

    Hi ZX299, I bought a set of these clamps off you a couple of months ago.
    Nice clamps but I found the smaller size, 40-44mm was too small. The next size up would be better.
     
  7. zx299

    zx299 Well-Known Member

    There's never been any problem....

    I checked with the supplier and they have never had any problem. ( Mine fitted perfectly)

    The only thing they could think of was that you may be using an oversized silicon hose. These clamp sets are for oem size hoses :cool:
     
  8. Madcow

    Madcow Active Member

    maybe it depends if you are using rubber or silicon hoses? I found the 3ply silicon hose OD was larger than the rubber hose OD.
     
  9. zx299

    zx299 Well-Known Member

    Non hard pipe version available.......

    I've had an enquiry regarding the non hardpipe version of radiator hoses. I spoke to the supplier and the non hardpipe (factory hoses) clamps will also be available as part of this GB.

    The non hardpipe clamps (4 clamps) will be available for $12.50 a set, so PM me for bank details if you still have the oem radiator hoses fitted to your zed
     
  10. pmac

    pmac Z,, IT'S COMPLICATED!!!!!

    Yea, could be a combination of the silicon hoses and after market radiator.
     
  11. zx299

    zx299 Well-Known Member

    Any more interest.....

    We've had a reasonable response so far (and the usual tyre kickers :mad:) so the GB will be closing in a couple of weeks.

    Put your hand up to get in on this GB or PM me if you have any queries :cool:
     
  12. zedsr4me

    zedsr4me Member

    Ian,
    I sent you a PM a couple of days ago re: confirmation.
     
  13. zx299

    zx299 Well-Known Member

    Group Buy closing this weekend.....

    PM me if you want to grab a set or if you have any questions :cool:
     
  14. _Robbo_

    _Robbo_ Active Member

    Ill jump in
     
  15. STocKi

    STocKi Member

    Your sending me broke Ian!
    ...sign me up :p;)
     
Thread Status:
Not open for further replies.

Share This Page