18th Item- Injectors Firstly, will only be selling 1 set of these. The other set will be fitted to my motor build. Set 1- Sard 650cc Injectors. Come with adaptors for Series 1 Fuel Rail and new o-rings. Receipt for recent ultrasonic cleaning, flow testing and o-rings. Modified top caps and screws included for clearance of upper plenum. 1 missing rubber in top cap, as shown in photo. Swap out for yours, and you're good to go. Sard 650's- $700 Set 2- Nismo 555cc Series 1 Purple Top Injectors Recently ultrasonic cleaning and flow testing through forum member Pennyarvs. New pintle caps and o-rings fitted. These are a direct bolt in for Series 1 fuel rails. Connector locating tabs filed down for connector fitment. Injectors have been marked for cylinder designation from previous owner. Nismo 555cc injectors- $600 Whichever sets sells first will decide as to which I will use myself. Cheers Michael
if i was u keep the nismos, sell the sards. Those sards fit supras with out all the hastle you get with them in zed rails, join the supra forum and you will sell them pretty quick
Yes, there are a few negative outcomes from sard injectors, of which yours is 1 iirc. Not going to hide or deny that they aren't a 300zx fit by design. With proper o-ring selection, as kindly posted by member Magicmike http://www.aus300zx.com/forum/showthread.php?t=299960&highlight=sard no issues should arise. The o-rings fitted were supplied by the testing workshop, and was told they they sealed in a 300zx fuel rail for flow testing. Either way, have to get rid of 1 set. Should it be the Nismos, will fit the sards to a rail and pressure test on my 2+2TT to guarantee o-ring seal prior to fitment. -Michael
I will be out of the country for a few weeks as of 9am tomorrow morning. Will not be in the position to sell/post any of the remaining sheer awesomeness listed above until my return. Taking your disappointment in mind, it is with the utmost reluctance that I lock this thread until my return. To those that hesitated and did not commit to purchase, I apologise for offering you this opportunity, and then so rudely taking it away.... like placing a fat kid in front of a closed candy store. Seek comfort in the fact that your chance will return. To those that have parts in transit, I will be checking the forum on a regular basis. If you have any queries or concerns about your parts, even after receiving, please do not hesitate to PM me, and I will respond in haste. -Michael
back in australia Following items have been sold:- 1- Altia 1/4 Illuminated Window Shades 3- 2k Spec Urethane Front Bar 9- OEM Nissan 1/4 Window Shades 10- Stillen Urethane GTZ Lip Spoiler 17- Unknown Front Strut Brace Following items have interest expressed:- 8- Seeries I Steering Wheel 11- 94+ Halo Wing 18- Nismo 555cc Injectors Gotta unpack camera, but will be posting detailed photos of the following:- 19th Item- Veilside Evolution 2+2 Catback Exhaust 20th Item- FULL Veilside Evolution 2+0 Exhaust (must be getting old.... tis a little too loud for my liking)
Item 19- Veilside Evolution Catback Exhaust to suit 2+2 Just opened the packaging for inspection. Will not get polished like the last (takes a while and costly). Few marks on underside of exit pipes from resonated centre section and minor scrape marks on underside of cannons. Bit of elbow grease will clean it up, but DIY mirror finish is certainly out of my attention span. $1100 plus freight fluffy black blanket again for display purposes only. Merrell Sneakers also not included in sale
Item 20- Nitrous Oxide Dual Shot Wet System and NOS Fmic Cooler Dual Shot Nitrous Wet System. Comes with:- * Brackets for 2 bottles * Intake hardpipes with nozzles fitted, Silicone couplers and T-Clamps * All lines (braided lines to hatch mounted NOS bottled yet to be removed) * Solenoids- NOS and Fuel * Jets (030 for NOS, 022 for fuel) * Purge * Gauge and t-piece for fuel line * Wiring- relays etc. Will throw in rocket switch for NOS when removed * Micro-switch and bracket (WOT trigger). NOS bottles not supplied. For local buyer, will throw in a '95 grey (rubber underlined) hatch carpet that has been cut up to accommodate bottles. Also included is a FMIC NOS cooling/spray system. * Hoop spray system that cable ties through the FMIC * Solenoid * Wiring * Braided line that runs along underside of car to hatch mounted bottle $500. This is the same system that Jason/zx2nv tried selling before his disappearing act for $1700 (claimed purchase price of over $3000) Honestly, have NFI what they're worth. Comparable prices on ebay are over $1000 for a dual shot wet system, without FMIC cooler. Jets indicate a 225HP Nitrous shot, but fuel jets arent matched. (again, NFI about NOS) Assuming NO responsibility for consequences or legalities of this install.
Item 21- Chili Master Cylinder Brace Possibly the most functional bl$ng available for the 300ZX. Made from shiny stainless steel stuff. Minor surface scratches, and the sticker has faded. Included, but not in photo, are the extended 6mm hex head screws for mounting. $70 posted Will even throw in the single thread of hair as shown in both photographs. Quite the rarity considering my ever thinning scalp.
1- Altia 1/4 Window Shades- SOLD 3- 2k Urethane Front Bar- SOLD 8- Series 1 Steering wheel with ACSD centre- SOLD 9- Nissan Option Tinted 1/4 Window Shades- SOLD 10- Stillen GTZ Urethane Front Lip Spoiler- SOLD 13- 1994+ Halo Style Rear Wind- SOLD 17- Unknown Brand 3-piece Front Strut Brace- SOLD 18- Nismo Series I 555cc Injectors- SOLD 19- Veilside Evolution 2+2 Catback Exhaust- SOLD 20- NAAAAWS- ON HOLD 21- Chili Brace- SOLD
Item 22- Complete Apexi Power FC kit Complete Apexi Power FC D-Jetro ECU setup. Same unit as listed by member Rob260 http://www.aus300zx.com/forum/showthread.php?t=312252&highlight=apexi+power Comes with:- * Apexi ECU * Apexi Hand Controller * G-Reddy switching unit (for VCT control) * Full 1995 ECU-Engine bay harness. Harness has been modified for Apexi ecu and has G-reddy switching unit spliced in. Harness is in VGC. Counted only 2 damaged retaining clips for coilpacks * TT Manual Balance pipe- fitted with twin outlets for MAP sensors * Two MAP Sensors * Temp Sensor (screws into side of plenum, utilising OEM vacuum outlet) * Installation manual.... in Japanese! * Dual intake setup. Twin K&N Pod filters and pipework that fits directly to turbo accordian pipes. You will have to remove the pipework that usually runs from the accordians to the MAF sensor. Was operational in car at point of removal (today). Tuned to OEM TT injectors. Asking $1200 for the lot
Item 1- Altia 1/4 Window Shades- SOLD Item 2- Airbag Steering wheel- Was $450 NOW $350 Item 3- 2k Spec Urethane Front Bar- SOLD Item 4- J-spec Fog Lights- Withdrawn from sale Item 5- Cargo Shade, perfect condition- Was $150 NOW $120 Item 6- Cargo Shade, needs edge glueing- Was $120 NOW $100 Item 7- Altia Sills, with non-oem inverter- Were $400 NOW $350 Item 8- Series 1 Steering wheel- SOLD, remaining ACSD and non horn pads- $20 each Item 9- Factory tinted Nissan 1/4 Window Shades- SOLD Item 10- Stillen GTZ Urethane Lip Spoiler- SOLD Item 11- Y32 Navan Wing- Still $250 Item 12- 1994+ Halo Wing- SOLD Item 13- 1994+ Halo Wing- Was $200, NOW $100, minus rubber mounts (used on my '95) Item 14- S14/ Z32 fit Navan wing, with LED Brake Light- Was $200, NOW $150 Item 15- Turbosmart BOV's with adaptors- Were $500, NOW $400 Item 16- UAS Ab-Flug copy front strut brace- Was $100, NOW $80 Item 17- Unknown front strut brace- SOLD Item 18- Nismo 555cc Series 1 Injectors- SOLD Item 19- Veilside Evolution 2+2 Catback Exhaust- SOLD Item 20- NAAAAAAAAAAAAAAAAAWS- SOOOOOOOOOOOLD Item 21- Chili Brace- SOLD Item 22- Apexi Power FC setup- Still $1200 Get in on the awesomeness. Have a bit of flexibility with the apexi ecu. Considering the length somebody has gone to with the harness modifications etc, would rather see it go on a 300zx than sell in to a skyrine owner